GC PRO UPDATE 47 INSTALL
GC PRO UPDATE 47 UPGRADE
GC PRO UPDATE 47 MAC

Solved by Connect pin 3 and pin 5 of jumper refer this section above. But if I remove both and try to reconnect then none of them work. I have only tried this with my thunderbolt displays if I connect one display to the card and leave it connected to the the card I can disconnect the second from the card or daisy chain and works after reconnecting.

Hot swap devices works till at-least one device is connected to the GC-TITAN RIDGE card.

GC PRO UPDATE 47 MAC

Note: I do not recommend or support installing unsupported macOS on your Mac Pro.

Mojave 10.14.6 (Officially supported with Metal supported cards).

I have tested this is working on the following Operating Systems: This test was done while on of the USB-C port was connected to 2 Apple Thunderbolt displays.

External SSD (mSata) Link connected via USB-C cable LinkР”В«lackMagic Speed Test with a mSata SSD.

MOTU 828mk2 Hybrid Audio Interface link.

The screenshot of the System Report with USB 3.1 and Disk Utility showing the attached Drive is as shown below: The USB 3.1 / USB-C port on the card worked successfully to connect to and transfer data to. The card is also detected successfully as a PIC Hardware as a thunderbolt and USB 3.1 device. I have also tried to Hot Swap the displays successfully.

You should see the OpenCore boot screen on your next boot.Р”Р„fter the Apple Thunderbolt Displays are connected to the system they work in Daisy Chaining and the following is shown in the System report. Shut down the Mac and do an SMC reset (unplug the power cord, wait 15 seconds, plug the power cord back in, wait 5 seconds, and then press the power button).Set the mounted EFI partition for booting bless -mount /Volumes/EFI -setBoot.Mounting the EFI drive using the command diskutil mount /dev/.Figure out the EFI disk using the diskutil list.Open the terminal and run the following commands to make your EFI drive bootable (bless) To boot into recovery mode hold down the Command (РІРЉВ) + R key after turning on the Mac Pro.Р”Р‡ollow the instructions on the official OpenCore documentation to OpenCore your Mac. Note: I used my original graphic card while I was trying to boot into the recovery drive. I got an alert asking to merge or update the contents. I already had a EFI folder within the drive.

GC PRO UPDATE 47 INSTALL

Install flashrom using brewР”В¬opy Contents of MacPro5.1 OpenCore.zip file into the mounted EFI drive The blue and the green chips that need to be flashed have a small dot with their respective colors.

Unscrew the 4 philips head screws to expose the PCB: Once you unbox your titan ridge card it should look like this: Source: Gigabyte Website Link Disassemble GC-Titan Ridge Here is a information about the package contents of Gigabyte GC-Titan Ridge Card Link.

GC PRO UPDATE 47 UPGRADE

My Upgrade Journey Gigabyte GC-Titan Ridge Card package contents

Custom firmware for the Gigabyte GC-Titan Ridge Card v2.0 Download.

EEPROM Flash Bios USB Programmer Amazon.

Obviously a Mac Pro and a Gigabyte GC-Titan Ridge Card Amazon.

My purchase and upgrade story can be found here ( Github View).

Processor: 2 x 3.33 Ghz 6-Core Intel Xeon (X5680).

My mac pro has the following configurations:

Please follow the links mentioned in the the Useful Links section below for more update to date information about the community postings on this topic. These steps have worked for me but there might be additional steps that might be required for getting other thunderbolt devices to work. This is not a end all be all guide for getting the GC-Titan Ridge thunderbolt card working for every use case. This is purely for educational purposes and I am not responsible for any void in warranty. I do not guaranty that this will work for you but I hope it does.

Before we begin a quick disclaimer below.Р”Вisclaimer: Try this at your own risk. This is my story to add Thunderbolt support to my Mac Pro Early 2009 (5,1) with a Gigabyte GC-Titan Ridge Card. Home РІвЂ“С‘ Thunderbolt Mac Pro Early 2009 with Gigabyte GC-Titan Ridge Card Thunderbolt Mac Pro Early 2009 with Gigabyte GC-Titan Ridge Card

Gc pro update 47